For a long time, "printing flexible" meant choosing between a 95A TPU, fairly easy, and an 85A TPU, much fussier. Over the last two years, filament makers have multiplied the variants: very hard TPUs designed to go through an AMS, glass-fibre reinforced TPUs, TPUs whose hardness changes with nozzle temperature or after printing. Recreus, the Spanish maker of Filaflex, has even launched its own filament diameter.

— Where the numbers come from

Every value in this guide comes from the manufacturers' data sheets and product pages (Bambu Lab, QIDI, Siraya Tech, Recreus, BIQU, colorFabb), checked on November 19, 2026, and from two independent tests named in the text (Hackaday and CNC Kitchen). We have not tested these filaments ourselves yet. Where two sources disagree, we say so. Prices are those shown by the shops that day and change often.

TPU: the basics

TPU (thermoplastic polyurethane) is the most common flexible filament. Its hardness is given on the Shore scales: A for soft materials (the lower the number, the softer), D for harder ones. A 95A TPU is flexible but holds its shape, an 85A bends between your fingers, and a 68D is much stiffer than a 95A.

  • The softer, the harder to print: a soft filament compresses and buckles between the drive gear and the nozzle. A 95A usually works through a Bowden setup if you print slowly. Below that, you need a direct-drive extruder with a well-guided filament path. That is what our compatibility tool checks.
  • Flow, not speed: TPU melts more slowly than PLA and compresses in the extruder. Manufacturers therefore often give a maximum flow in mm³/s rather than a speed. Our flow calculator converts one into the other.
  • Moisture: TPU picks up moisture within one to three days in open air. Our humidity guide recommends 50 to 55 °C for 4 to 8 hours for a standard TPU. Some filaments below call for other values: follow the manufacturer's sheet then.
  • AMS and spool changers: most soft TPUs do not go through multi-spool systems (AMS, CFS, MMU). Manufacturers state it product by product, and we note it for each one.

For standard TPUs (95A, 85A, high-speed TPU) and TPE, average temperatures and prices are in the filament comparator, for example the TPU 95A page.

Stiff TPU: 68D for the AMS

To get TPU through an AMS, Bambu Lab relies on a much harder filament. Its TPU for AMS is rated 68D on its data sheet, far harder than a 95A. You keep a material that takes impacts well, but parts are no longer really "soft".

Bambu Lab TPU for AMSOfficial data sheet
Hardness68D
Density1.26 g/cm³
Nozzle220 – 240 °C · 0.4 / 0.6 / 0.8 mm nozzles
Bed30 – 35 °C, textured or smooth PEI with glue
Chamber25 – 45 °C (part cooling fan on)
Speedunder 250 mm/s · retraction 0.8 – 1.4 mm
Impact (Charpy)124.3 kJ/m² in X-Y, but 9.6 kJ/m² in Z (across layers)
Drying70 °C for 8 h in a drying oven
Spool1 kg, 1.75 mm

The gap between impact strength in the plane (124.3 kJ/m²) and across layers (9.6 kJ/m²) is the key point: orient the part so loads don't pull layers apart. It is the easiest TPU to use on a Bambu Lab printer with an AMS, as long as you are not after real softness.

TPU-GF: glass-filled TPU

TPU-GF adds about 15 % short glass fibre to a hard TPU base. QIDI and Siraya Tech (Fibreheart range) each sell one, with nearly identical data sheets. The result is not a soft filament: it is a stiff but elastic material that damps impacts and vibration, without stretching like a 95A.

PropertyQIDI TPU-GFSiraya Tech Fibreheart TPU-GF
Glass fibre15 %15 %
Hardness67D67D (data sheet; the product page also says 64D)
Density1.32 g/cm³1.32 g/cm³
Tensile strength (X-Y)30.9 MPa32 MPa
Elongation at break (X-Y)74.8 %80 %
Charpy impactno breakno break
Vicat (softening)157.3 °C157.3 °C
Nozzle240 – 270 °C240 – 270 °C
Bed35 – 60 °C40 – 60 °C
Speed30 – 120 mm/s30 – 100 mm/s
Nozzle requiredhardened steel or bimetal, no 0.2 mmhardened steel, 0.4 mm or larger
Drying70 – 80 °C, 4 – 6 h50 – 60 °C, 6 h or more
Multi-spoolQIDI BoxAMS, AMS Lite, AMS 2 (per Siraya)
Price seen$39.99 per kg$39.99 per kg ($34.39 on sale)
  • What the makers claim: little or no warping, parts that come off the bed more easily than standard TPU, less stringing, good resistance to oils, grease and fuel. QIDI even says it can replace ABS in some cases. None of this is quantified.
  • A hardened nozzle is mandatory: like every filled filament, TPU-GF wears a brass nozzle. Both makers rule out the 0.2 mm nozzle.
  • Mind the AMS: Siraya says its TPU-GF is AMS compatible, but its own sheet warns that glass fibre can speed up wear on the AMS's plastic filament paths and feeder gears. QIDI recommends a direct-drive extruder.
  • Drying differs: QIDI asks for 70 to 80 °C, Siraya 50 to 60 °C. Follow the sheet of the brand you buy.

TPU-GF is meant for functional parts: robot bumpers, anti-vibration feet, mounts that must flex without breaking. For a truly soft part, it does not replace a 95A.

Recreus Filaflex 2.20 mm

Recreus, the maker of Filaflex, showed the Filaflex 2.20 System at Formnext in November 2025: a flexible filament 2.20 mm in diameter and a matching hotend. Launch kits have been on sale since March 2026. It is a third diameter, between the two market standards.

Why 2.20 mm?

Recreus starts from the weaknesses of the two existing diameters when the filament is soft:

  • 1.75 mm: it melts quickly, but such a thin, soft strand buckles under the extruder's push as soon as you speed up. That is what limits the speed of soft TPU.
  • 2.85 mm: it handles the push well, but its mass makes it melt slowly, which caps the flow.
  • 2.20 mm: a cross-section 58 % larger than 1.75 mm and 2.3 times the buckling resistance according to Recreus, while keeping, it says, heating efficiency close to 1.75 mm.

Bambu Lab made a related choice on the H3C, whose FlexFeed extruder takes 2.85 mm filament to print TPU down to 75A. Recreus instead offers an in-between diameter and fits it to existing printers.

Claimed flow rates

Recreus publishes these volumetric flows, 0.4 mm nozzle, going from 1.75 mm to 2.20 mm:

Filaflex1.75 mm2.20 mmClaimed gain
60A2 mm³/s8 mm³/sup to 3.7×
70A3 mm³/s11 mm³/s3.3×
82A and Foamy6 mm³/s15 mm³/s2.3×
95A and 95 Foamy7.5 mm³/s18 mm³/s2.4×

These are the manufacturer's figures. Recreus says it validated the system over more than 1,000 hours of printing without a clog (TPU, PLA and PETG). As far as we know, no independent test of these flow rates has been published.

What you need to use it

  • A 2.20 mm hotend: you replace the stock hotend with Recreus', whose channel is 2.3 to 2.4 mm. According to Recreus, it also prints rigid 1.75 mm filament (PLA, PETG, ABS, PC) without an adapter. The 2.20 mm filament, however, does not fit a stock 1.75 mm hotend.
  • Supported printers: from Bambu Lab, P1P, P1S, X1, X1C, X1E, P2S, H2S and H2D; from Prusa, MK4S, Core One, Core One L and Prusa XL. Recreus publishes an installation guide for each model.
  • Price: the Bambu Lab hotend is listed at $43.95 (P1P/P1S and X1) and $36.95 (P2S/H2S/H2D) on the Recreus shop. Starter kits (hotend + first spool) exist for Bambu Lab and Prusa.
  • No AMS: Recreus asks for a direct-drive extruder with the spool on an external holder, without AMS or MMU. Multicolour support is announced as "in development".
  • Settings: Recreus does not publish a temperature table. You generate a slicer profile on its website by choosing the printer, nozzle and diameter. The one shared tip: dry Filaflex at 55 °C for at least 1 hour.

Filaments in 2.20 mm

The 2.20 mm range follows the Filaflex hardnesses: 60A, 70A, 82A and 95A, plus the foaming Foamy and 95 Foamy, Reciflex and Conductive Filaflex. It is a Recreus format, covered by a pending patent. Recreus is looking for partner manufacturers to adopt it, but for now it is the only one selling it. Fabbaloo, which analysed the announcement, expects the system to stay a niche product as long as 1.75 mm dominates the market.

BIQU MorPhlex: 90A → 75A

BIQU's MorPhlex (BIQU is BigTreeTech's brand) is sold as a "variable hardness" TPU: it prints like a 90A, stiff enough to feed through an extruder, then becomes a very soft 75A once printed. BIQU does not explain the mechanism, nor how long the change takes.

BIQU MorPhlexOfficial product page
Hardness90A when printing, 75A afterwards (75A ± 3A on the sheet quoted by Hackaday)
Nozzle225 – 260 °C
Flow2.8 – 4 mm³/s
Diameter1.75 mm ± 0.02 mm
Spool1 kg, vacuum-sealed with desiccant
AMSnot compatible: bearing spool holder recommended
Coloursbeige, black, purple, orange, blue, Nova Blue, red, grey, yellow
Price seen$69.99 on the BIQU store
  • What it is for: BIQU targets shoes, slippers, insoles and soft grips, and recommends segmented shoe models.
  • High temperature range: 225 to 260 °C is hot for a TPU. The reseller MakerParts advises against reusing your usual TPU settings as they are.
  • Drying: BIQU asks you to dry the filament fully before printing, without giving a temperature or time. Failing that, the TPU values from the humidity guide (50 to 55 °C) are a reasonable starting point.
— Independent test: more like 80 – 85A

In August 2025 Hackaday covered a test by the ModBot channel, printed on a Bambu Lab H2D: on a durometer, the parts measured 80 to 85A (depending on the face measured), above the advertised 75A ± 3A. Hackaday therefore wonders how much temperature and extrusion speed affect the final hardness. The tester also recommends glue on the bed, as parts stuck hard.

Foaming TPU

Another way to get a part softer than standard TPU is to make it foam. These filaments contain a foaming agent that releases gas above a given temperature. The hotter the nozzle, the more the plastic swells, and the lighter and softer the part.

colorFabb varioShore TPU

  • How it works: printed between 190 and 200 °C, it does not foam and stays hard. Between 200 and 250 °C, it expands up to 1.4 to 1.6 times its volume, and its density drops from 1.2 – 1.3 to 0.7 – 0.9 g/cm³.
  • Hardness: from 95A unfoamed down to 55A at maximum foaming, according to colorFabb.
  • Flow: colorFabb recommends printing at 60 – 70 % flow to make up for the expansion.
  • Listed uses: prosthetics (skin tones available), shoe soles, bike grips, light parts with a soft touch. An 85A version also exists for insoles and protective padding.
  • Spool and price: 700 g, €54.20 for the 95A version on the colorFabb shop (before discounts).

CNC Kitchen's test qualifies these figures: maximum expansion is reached around 220 °C (and drops above it), it measured up to twice the volume, and a minimum hardness around 65A. It had to tune the flow for each temperature: 113 % at 190 °C, without foaming, and 57 % at 220 °C. Expect a few test prints before you find the right setting.

Recreus Filaflex Foamy

Recreus also sells foaming versions, Foamy and 95 Foamy, available in 2.20 mm among other diameters. According to Recreus, at 100 % flow the line widens by about 37.5 %: its profiles already reduce the flow. To make parts even lighter, Recreus suggests lowering the flow in 5 % steps (down to 60 %) and the volumetric speed by 10 to 15 %.

Summary table

Manufacturer values, prices seen on November 19, 2026 on their shops:

FilamentHardnessDiameterNozzleAMS / multi-spoolPrice
Bambu Lab TPU for AMS68D1.75 mm220 – 240 °Cyes (designed for it)n/a
QIDI TPU-GF67D, 15 % glass1.75 mm240 – 270 °C, hardened nozzleQIDI Box$39.99 / kg
Siraya Fibreheart TPU-GF67D, 15 % glass1.75 mm240 – 270 °C, hardened nozzleyes per Siraya (possible wear)$39.99 / kg
Recreus Filaflex 2.2060A to 95A2.20 mmRecreus profile, dedicated hotendnohotend $36.95 – $43.95
BIQU MorPhlex90A → 75A1.75 mm225 – 260 °Cno$69.99 / kg
colorFabb varioShore TPU95A → 55A (foamed)1.75 / 2.85 mm190 – 250 °Cnot stated€54.20 / 700 g

Which one to choose

  • You have a Bambu Lab printer with an AMS and just want parts that take knocks: TPU for AMS 68D is the simplest. It will not give you a soft part.
  • You want a stiff part that damps (feet, guards, mounts that flex): TPU-GF, with a hardened steel nozzle of 0.4 mm or more.
  • You print a lot of soft TPU on a compatible Bambu Lab or Prusa and the slowness bothers you: Filaflex 2.20 is the only offer that promises a real flow gain, at the cost of a specific hotend and a filament sold by a single brand.
  • Slippers, soles, very soft grips: MorPhlex prints more easily than a true 75A. Expect something closer to 80 – 85A according to Hackaday's test.
  • Light parts, foam feel, floats: a foaming TPU (varioShore or Filaflex Foamy), with a few test prints to tune temperature and flow.

In every case: dry the filament, print with a direct-drive extruder once you go below 90A, and check in our compatibility tool what your printer can handle. If your machine is Bowden, moving to direct drive is one of the upgrades that actually matter.

Sources: Bambu Lab TPU for AMS data sheet; QIDI TPU-GF product page and Siraya Tech Fibreheart TPU-GF data sheet; Recreus, "The 2.20 revolution" and its print parameter pages; BIQU MorPhlex; Hackaday; colorFabb varioShore TPU; CNC Kitchen; Fabbaloo.

G_54 · published 11.2026 by Louis Compatibility tool → Filament comparator →