Elegoo made its name in resin, then in FDM with the Centauri Carbon and Carbon 2, low-priced enclosed CoreXY printers. With the Centauri X Ultra, the brand moves to a toolchanger: several complete heads, each with its own filament, instead of a single nozzle that purges at every colour change. It joins the Snapmaker U1, the Creality K3 and the Bambu Lab H3C in a segment that filled up quickly in 2026.
Confirmed by Elegoo (press release of November 18): four independent printheads, quick head switching to reduce waste, rigid and flexible materials. Reported by the press from the booth panel (Psych0h3ad, China-Gadgets): 256 × 256 × 256 mm, 500 mm/s, 350 °C nozzle, 120 °C bed, ~5 s head swaps, 4 spools in two boxes heated to 65 °C. Elegoo has not published a spec sheet on its website yet, and the press notes these figures may change before release. Not announced yet: price, release date, pre-orders, regions, chamber heating, camera, connectivity, weight.
What was announced
The Centauri X Ultra was shown at Formnext 2026 (Messe Frankfurt, booth 12.0-C02, until November 20) "without prior announcement", according to Elegoo. The press release of November 18 calls it an "upcoming FDM 3D printer" and a significant milestone for the Centauri series as it moves to multiple printheads. It says very little about the hardware: four independent printheads, quick head switching that "helps minimize material waste during color changes", and support for rigid and flexible materials, for multi-colour and multi-material printing.
The more detailed figures come from the information panel on the booth, photographed and reported by several sites including Psych0h3ad and China-Gadgets. Both give the same values. The machine on display is described as a prototype: in the photos the top of the enclosure is open, while the panel says a top cover is included as standard.
On the same day, Elegoo also showed a resin printer, the Saturn 5 Ultra (planned for early 2027, see our Elegoo resin guide), and its first 3D scanner, the M1 Ultra.
4 heads, ~5 s swaps
On a single-nozzle printer with a multi-colour unit (like the Carbon 2's CANVAS), every colour change means unloading the filament, loading the next one and purging the nozzle. A toolchanger keeps each filament loaded in its own head: the machine parks the active head and picks up another.
- Four complete heads: each with its own nozzle, extruder and filament. The panel lists a dual-gear direct-drive extruder with a 7:1 gear ratio.
- About 5 seconds per head swap, according to the panel. That is in the same range as the Snapmaker U1 and the Creality K3.
- No purge with one colour per head: according to China-Gadgets, Elegoo claims zero purge waste as long as each head keeps a single colour or material. A purge tower would still be needed.
- Beyond 4 colours, waste comes back: see AFS below.
Elegoo has not named the swap mechanism or explained how the heads are docked and aligned with each other. The panel only mentions automatic calibration and vibration compensation. Psych0h3ad notes that the PTFE tube routing near the toolhead looks tight on the prototype: that is an observation, not a manufacturer figure.
Specs (show panel)
These values come from the panel displayed at Formnext, as reported by the press. They are not on Elegoo's website yet and may change before the production version.
| Spec | Elegoo Centauri X Ultra (prototype, Formnext 2026) |
|---|---|
| Technology | Fused filament fabrication (FFF / FDM) · toolchanger |
| Printheads | 4 independent heads |
| Head swap | ≈ 5 s · no purge with one colour per head (Elegoo claim) |
| Build volume | 256 × 256 × 256 mm (same as the Centauri Carbon 2) |
| Max speed | 500 mm/s |
| Max nozzle temp | 350 °C |
| Heated bed | up to 120 °C (100 °C in 3.5 min according to the panel) |
| Extruder | Direct drive, dual gear, 7:1 ratio |
| Spools | 2 transparent side boxes of 2 spools each, heated up to 65 °C · RFID · automatic filament loading and recovery |
| More colours | up to 20 colours with the AFS add-on system |
| Materials | PLA, PETG, TPU, ABS, PA, PC · rigid + flexible combinations |
| Features | Automatic calibration · vibration compensation · quiet mode · "Cooling Mode" for PLA and PETG |
| Screen | 5-inch flip-up touchscreen |
| Enclosure | White · top cover and drying boxes included as standard |
| Dimensions | 613 × 462 × 510 mm (spool boxes included) |
| Not announced | Chamber heating, acceleration, nozzles (sizes, hardened or not), camera, connectivity (Wi-Fi, LAN), firmware and slicer, weight, power draw, noise level |
The base borrows a lot from the Centauri Carbon 2: same 256 mm volume, same 350 °C nozzle, same rated speed and 5-inch screen. The bed goes a little hotter (120 °C versus 110 °C on the Carbon 2).
Heated spool boxes & AFS
Instead of a separate unit beside or on top of the printer, the X Ultra carries its spools on its sides: two transparent boxes, left and right, each holding two spools, so one per head.
- Built-in drying: the boxes heat up to 65 °C. That is enough for PLA, PETG or TPU, and to keep already-dried filament dry. For PA and PC, which often need hotter and longer drying, see our filament & humidity guide and the drying calculator.
- RFID: the boxes read spool tags and handle filament loading and recovery automatically.
- AFS, up to 20 colours: the panel mentions an add-on system called AFS that would take prints to 20 colours. Elegoo has not detailed it yet (how it works, price, included or not). An important point raised by Psych0h3ad and China-Gadgets: with AFS, several colours go through the same head, so the "zero purge" claim no longer applies.
X Ultra vs Carbon 2, U1, K3 & H3C
Where does the X Ultra sit among multi-tool printers? Since its price is unknown, the comparison is technical only. Prices for the other machines are indicative.
| Machine | Approach & nozzle | Volume (mm) | Price ≈ |
|---|---|---|---|
| Elegoo Centauri X Ultra | 4-head toolchanger · 350 °C · 65 °C heated spool boxes | 256 × 256 × 256 | not announced |
| Elegoo Centauri Carbon 2 | Single nozzle + 4-colour CANVAS (Combo) · 350 °C | 256 × 256 × 256 | ≈ €450 (≈ €570 Combo) |
| Snapmaker U1 | 4-head toolchanger · 300 °C | 270 × 270 × 270 | ≈ €850 |
| Creality K3 | KliTek 4-nozzle changer · 300 °C | 260 × 260 × 260 | $849 (US) |
| Bambu Lab H3C | 9-tool toolchanger · 350 °C · 65 °C active chamber | 330 × 320 × 325 | $2,499 / €2,499 |
- vs Centauri Carbon 2 Combo: same volume and nozzle, but the Carbon 2 changes colours with a single nozzle and purges each time. The X Ultra avoids that purge as long as you stay at four colours or materials, and allows real rigid + flexible combinations.
- vs Snapmaker U1 and Creality K3: the same four-head formula with about 5 s per swap. On paper, the X Ultra runs hotter (350 °C versus 300 °C) and has built-in spool drying. The U1 keeps a slightly larger volume.
- vs Bambu Lab H3C: the H3C plays in another league (nine tools, actively heated chamber, bigger volume, $2,499). Everything will depend on the X Ultra's price.
For the full overview of the technologies, see our multi-tool printer landscape and the printer comparator.
Price & availability
As of November 19, 2026, Elegoo has announced no price, no release date and no pre-order. The booth panel did not give any either, and no crowdfunding campaign has been mentioned. The regions where it will be sold are not known yet.
The only timing in the press release concerns the Saturn 5 Ultra (resin), shown the same day and planned for early 2027. Nothing similar is said for the Centauri X Ultra. We will update this article as soon as Elegoo publishes a price or a date.
What we don't know yet
The show spec sheet looks promising, but this is a prototype and many points remain open:
- The price, which will decide everything: against the Snapmaker U1 and the K3, the X Ultra will need to land near their prices to stand out.
- The chamber: nothing points to active chamber heating. For large ABS, PA or PC parts, that matters.
- The nozzles: neither size nor material (hardened steel or not) is given, while the Centauri Carbon ships with a hardened nozzle.
- The AFS system: how it works, its price and the real waste beyond four colours.
- The reliability of the changer and tube routing, the camera, connectivity and software.
- Final specs, which may still change before release.
Our take: on paper, Elegoo takes the Carbon 2 base and adds what it lacked for multi-material work: four real heads and heated spool boxes. If the price follows the brand's habits, it could be a serious rival to the U1 and the K3. Wait for the price, the official spec sheet and the first reviews before deciding. In the meantime, the Centauri Carbon 2 Combo remains Elegoo's multi-colour option available today.